Woodshop Benches

Posts Tagged ‘Turning’

Woodshop BenchesBowl Turning – Introduction

In the winter of 2010, I decided to pursue private study of the transformation of a bowl. I read all the books I found and watched videos from YouTube several times before buying my Nova DVR XP tower, inches 1 / 2 of the Crown and the bowl 3 / 4 inch gouge, a tool of separation, a large spatula Makita angle drill, belt sander, orbital sander, grinder, chainsaw Sthil, polishing wheels, abrasives, sandpaper, CA glue, walnut oil, shellac, wax, cloth, wood to build a solid mounting surfaceTour of sandbags to stabilize the table. I never took wood shop and I have no previous experience of turning bowls. I built a log cabin, 2 factories in Canada and has always had a love for wood and trees.

I ordered most of my devices turning in the catalog and have been surprised by how the tools and equipment to my expectations and was a breeze.

At the same time, I built my tour (for Nova DVR specification downloadvia the Internet), I decided to look for sources for newspapers. I put ads on Craigslist, asking for large log which led to some of my Dutch elm newspapers large and medium-sized enterprises Cypress newspapers. I also called several fuel suppliers, many newspapers have no provision or wood that was favorable to the lathe. However, a tree cutter got in touch with me and a true love of wood and interest in helping me to find good wood. He took me to his storage yardI found a large diameter logs, cedar, oak, walnut and black walnut wood slabs that his father had saved and protected.

On another occasion I stopped a yard for firewood in the hills and overlooking an endless supply of huge towers of ash, oak and unknown species. I immediately had a good supply of discs stacked in the shade of an avocado tree in my yard and lined with plastic sheeting. I kept records on the floor with pieces of wood and Iwas lying. On average, excluding the black walnut, which was expensive, I could fill my Ford Explorer with big pieces of wood of $ 40 to $ 60. In comparison, a visit to the shops that offer a white bowl, I found most areas were selling to small and expensive. A virgin can cost as much as a truck un-split firewood.

Do not have a garage to the house of my team, I built a small shelter, using wood and a tarp to protect my work area. I use a briefcase to protect my gardenJourney into the shed. My tools are readily available from a shelf under the counter.

Deliberately avoid buying expensive equipment like a saw or band instruments are not needed as guides to correct, etc. My intention was to create a natural-rustic dishes with the equipment as possible.

There are many opinions on what materials and tools are needed, how to handle your tools, how to sharpen your tools, what is the right to use the wood, which is aacceptable container … I decided to plow through it, do my thing and learn as I go. Chainsaw, round, bowl gouge, sander and grinder are the heart of everything we do.

I started to try the dishes of other artists in the artist's shops and online. I saw the most beautiful finishing hole forms sat behind a glass shelves … Only $ 800.00! I found websites with very nice bowls for sale at a lower price I can not imagine how the artist can pay for your offer of the day.These comments left me puzzled and, again, I decided to do my own thing and see what happens.

My lack of experience and interest in a utility rotating bowl made me think that my work was disparaged by professional experts. It 'was to my surprise, many of my dishes, sold at silent auctions or private, were pieces that had visible cracks sealed irregularities, the surface or sides distorted. It was then that I realized I did not need anything else pleaseartists, people who are the imperfections of the most interesting and I must admit that when a fruit salad or a mixture is placed in a container with several flaws, the overall look is very attractive. I had friends remember not to go too far the rustic charm of my first pieces and took his suggestion to heart.

The Tour

I love my Nova DVR XP. I looked at many other models, including those who can pay and those who move at low costBelt pulleys through the speed of change. Now that they have actually done bowling, I can not think of anything to help, but a constant visits variable speed drive that allows you to directly change the speed at the touch of a finger on the keyboard. This does not mean that the DVR XP is absolutely perfect … outside the large round white can do the hard work of my bank to move at high speed, the safety mechanism that stops the machine in a "catch" can be easily removed with greatWhite, running at low speed, and there were minor problems, such as loosening a nut inside the case. I learned how to improve or solve these problems with great satisfaction. I have not tried the extra support to make the containers more than 16 inches in diameter, but I imagine there will be some taxes from the tower and my workstation. The DVR was $ 2,200.00 and was buying the ticket as it is wide. It was delivered through my driveway and the driver helped me to collect moremy workstation.

Why is it so important to be able to change gears quickly? You know the answer to this question when you make your first drink. Initial speculation, speculation, finally, scraping, sanding, apply a finish, shiny … using a wide range of speed to perform these tasks.

Breaking the rules

There is nothing wrong with being a strict discipline. There is nothing wrong with the training and education. And 'in my nature to go alone, and most of thethe fun is learning on the fly and experiment with their ideas. For example, Everything I've read and seen the video that appears in the bowl rotation of the mounting cup-shaped container, then the bowl to form inside the container. This involves the use of a front panel and then use a spindle for the remainder of the session. I was surprised to learn that I could get in and out, never remove the cap and there are holes in the bottom of mybowl. Why does not anyone say this?

The use of exotic woods and not expensive, I am free to increase the depth of my empty plate to the length of the screws used to secure the front. I train from the tank, 75% of the fund, leaving only the section of wood in front of the machine of the United Nations, avoiding cutting too close to the plate. I can, without removing the empty space, the shape of the rim and inside of the container and follow the development of grinding and polishing. Then use aseparation of instruments and, finally, a hand saw to remove unwanted wood to the front of the bottom of the cup. A belt sander will be lower.

Another rule switch is turning green or wet wood. I found that the results depend on the wood, the amount of moisture and its willingness to tackle the problems of distortion. The available data show that can transform a preliminary version of the cup with a uniform thickness and put the container aside for a few months in a cool place. I read thatyou can put the container in paper bags until the moisture is most evident in the bag. I am now, too impatient to wait several months and the only time I tried the paper bag trick, the dish was covered in mold and to the left.

When a forest fire damp or wet, one of three things. 1) The deformation bowl. One of my most valuable pieces was a bowl of Dutch elm distorted. 2) cracks. CA glue is for. It works very well and learn to make better use ofresults. You can rub your hand at the end of glue-soaked sawdust AC crack, apply a thin tail of CA. Powder coating of wood for a light rinse to balance the things you will be able to load sand in less than an hour. The CA glue and / or fill the cracks immediately visible, during and after the shooting and, if necessary during the drying process. Well, if you want to turn precision parts free of defects that do not work. 3) The process of finishing should be delayed. Lacquerdries matte. Hardening oil locks in moisture. The bowl in hand, can happen until the end. Depending on the amount of moisture and the type of wood that can last a few days or weeks. However, a layer of green walnut oil in all my dishes immediately after turning and grinding. I was polishing the bowling from 80 to 400 grit, wipe a layer of walnut oil, re-sanding with 220-400 grains down any raised grainThen put the bowl aside. As the container is booked more likely that the container is deformed and will not be able to lift the vessel on the lathe for speculation or additional sanding tower. 4) There is nothing bad happens. I'm surprised, but it's true … has happened many times. I turn a container of wet sand that the chicken, clean it with walnut oil, leave it in a cool house, which runs on top of paper bags and the cup comes in handy. I also asked coatsspray lacquer shortly after. Ok, tin matte painting or a hole, if the water is clear and lucid or necessary. I had two bowls developed dark spots on the paint and I'm having a hard time removing. Now I'm leaving tendency to dry the dishes after sanding with a single layer of walnut oil is rubbed into the wood.

The end result: a problem with the cracks that have been repaired with glue CA (fine, medium or large) andI had a sprain or re-machined to remove, I have many pleasant decor bowls without any problem. I made three dishes are wet or damp in the last week. One was oblong, there are bumps along the edge, two are in good condition. Both have a minor disfigurement were so wet that my face was flat during the shooting mat. The two that were normal, except that when I re-edge, moist but not saturated.

End

I experimented with walnut oil, whichThey told me that is not bad, different disinfectant hand-finished, polyurethane, paint, beeswax, carnauba wax, polishing compounds, etc. Lacquer (layers 3-4) gives a gloss finish and lasts if you wait a couple of weeks fan out like glass. Can I use aerosols purchased for $ 10 for Rocklers pop. It took me a while 'for the technique, take heart.

I sand the lacquer finish of walnut oil, and / or carnauba wax finish in the shortest possible time, but nothing can beat the application finishesand to harden or set before polishing. I just got a deal Beal buffing system for the tour. It 'amazing! There are three big wheels of polished thick, a large bar of the compound in Tripoli to take the cast, a big bar of polished white diamond and a bar end carnauba wax to the finish. I tried it in a bowl of paint that had been polished with a small wheel, made of Tripoli and carnauba wax. The difference between the usewheel separately for each compound and the combination of Tripoli, White Diamond, carnauba was great to see. The container is finished in real glass.

More recently, I was watching Elmer Adams (deceased), videos on YouTube. The way he finished his big mouth is to immerse the pot in a 4 Deft Danish oil and a solution of Defthane clear in a bathtub for 12 hours, completely saturate the container. It removes the oil and then apply five coats of the same mixture by hand polishing eachlayer of a compound of Tripoli, with a mixture of white diamonds and wax renaissance the last layer. No sprays, no nail polish … People told me that a dish of saturated oils take forever to dry. I'll try a more traditional approach with pure tung oil cut 01/04 with a diluent to facilitate penetration, followed by 1.2 applications thin tung oil, with 24 hours of drying and sanding between the hands.

Spend money than make money

My motivation for not making money bowls.However, fans do not want this to be a hole all the extra money in the sale of the dishes I make. At first, it seems that it is experimenting with materials, tools and materials that continue to accumulate charges on your credit card. By avoiding the purchase of luxury equipment that can do without and improve the process of shooting and finishing, the amount of time and effort I put in a pot is down. Once you know how to select and tools to improve myparticular task, the most efficient and empty the container, and understand the most direct method to develop a beautiful finish that will have a systematic approach to the creation of a bowl that others find pleasant. At this point, the cost per plate to stabilize and I could see the performance increase accordingly. Well, this is not a year to turn around, but I'm here for the long term and I like it. I told my wife when I retire, I sell every dish is a meal for two or a nightthe city. I also intend to pay the cost of factors, including raw wood to turn.

Woodshop Benches

Woodshop BenchesTurning tools and equipment for beginners

Pursue a career as a landmark of wood can be a daunting prospect for novices. This is because there are a variety of tools and specialized equipment. Purchase of equipment and accessories for your new business can be extremely addictive. To keep the initial costs of starting at least it is useful to identify elements that are necessary and can be added at a later time.

Purchases of essential tools for turning and equipment for beginners will probably cost a total of four digits.Of course, that is, if you buy new. There is always a large number of items sold on eBay for experienced carpenters just moved into a rounded tip, tools or equipment. This can save you hundreds of dollars on their initial investment.

The first piece of equipment you need is a lathe of wood. This in itself can be confusing, because it is often difficult to choose between the permanent tower, with small mini-tower. The smaller towers are great if space is an importantproblem and you are 100% sure that will never be able to convert the larger objects. If this is not the case, you should invest in a tower stand.

Your turn will come again with probably the base for the team as a breastplate, and training centers. You will need to integrate these products, investing in a grip of wood carried out correctly. The four jaw chucks are the most popular and have a wide range of optional jaws for different sized projects.

ThenReturning to the question of turning tools and this is an area that tends to get what you pay for. Note that the market is flooded with cheap and inferior tools, can be attractive to newcomers. Expect to pay about 120 tickets for a series of six wood-turning speed steel tools of high quality. It will be money well spent and cheaper in the long term to replace broken instruments of poor quality.

The last piece of equipment is a system of tool sharpening. You need to keep cutting tools to ensurea clean cut. Many turners experts swear by the plant to the bench a good age. These wheels can be fitted with special blue or red for sharpening tools in HSS. Otherwise, there are many sharpening systems designed specifically to sharpen the tools to transform high-speed steel.

These are the basic tools, but the film and equipment essential for beginners. Follow a small amount of kit and its budget is not out of control. These elements areyou can learn the art of wood turning, to develop their skills and become a skilled wood turner. As your skill level to improve, is the appeal to add additional tools and equipment irresistible.

Woodshop Benches